Bolt-on-mods.com

BOLT ON MODS

Dodge Viper Flip Key with FOB 2003-2010

from 59.99
IMG_6338.JPG
IMG_6332.JPG
IMG_6339.JPG
IMG_6336.JPG

Dodge Viper Flip Key with FOB 2003-2010

from 59.99

This is the flip key mod for the 2003-2010 Dodge Viper. These are a great update for the Viper, or just great to have as a back up. Brand new with batteries, electronics, flip key and fob.

These are all ready to go and just need to be cut and fob programming (See below for instructions). 

**FREE SHIPPING

Instructions:

YOU MUST HAVE A WORKING REMOTE FOR THIS PROCEDURE TO WORK. IF YOU DON'T HAVE A WORKING REMOTE THEN YOU MUST HAVE A REMOTE PROGRAMMED BY A DEALER OR LOCKSMITH USING DIAGNOSTIC EQUIPMENT. PLEASE READ ENTIRE PROCEDURE BEFORE PERFORMING. SOME VEHICLES MAY USE ONE OF TWO PROCEDURES.

Procedure: 

Obtain all remote transmitters for this vehicle.

1. Put key in ignition and turn ignition switch to ON position (as far as you can turn key without cranking engine).

2. Press and hold UNLOCK on a currently functioning remote for 4 to 10 seconds.

3. While holding the UNLOCK button during the 4 to 10 second period, press the panic button for one second and release both buttons at the same time. A chime should sound within three seconds to indicate the vehicle has entered programming mode.

4. Press the LOCK and UNLOCK buttons simultaneously on the same remote used in step 3. then release. You should hear an audible tone indicating that the remote was recognized. Once tone is heard press and release the UNLOCK button on that remote. A chime should sound indicating that the remote has been programmed. This must be done within 30 seconds of step 3. Within 30 seconds of completing step 4. press the LOCK and UNLOCK button on the next remote then release. You should hear an audible tone indicating that the remote was recognized. Once tone is heard press and release the UNLOCK button on that remote. A chime should sound indicating that the remote has been programmed.  

5. Repeat step for all additional remotes including working remotes.

6. Programming is now complete. Turn ignition off and test remotes to ensure proper programming.

If this does not work may more attempts. ****PLEASE NOTE**** If you have issues with programming run through the process even if you're not correctly hearing the chimes. Some vehicles have went through programming succesfuly and did not chime as stated in directions. 

With Viper Decal:
Quantity:
Add To Cart

This is the flip key mod for the 2003-2010 Dodge Viper. These are a great update for the Viper, or just great to have as a back up. Brand new with batteries, electronics, flip key and fob.

These are all ready to go and just need to be cut and fob programming (See below for instructions). 

**FREE SHIPPING

Instructions:

YOU MUST HAVE A WORKING REMOTE FOR THIS PROCEDURE TO WORK. IF YOU DON'T HAVE A WORKING REMOTE THEN YOU MUST HAVE A REMOTE PROGRAMMED BY A DEALER OR LOCKSMITH USING DIAGNOSTIC EQUIPMENT. PLEASE READ ENTIRE PROCEDURE BEFORE PERFORMING. SOME VEHICLES MAY USE ONE OF TWO PROCEDURES.

Procedure: 

Obtain all remote transmitters for this vehicle.

1. Put key in ignition and turn ignition switch to ON position (as far as you can turn key without cranking engine).

2. Press and hold UNLOCK on a currently functioning remote for 4 to 10 seconds.

3. While holding the UNLOCK button during the 4 to 10 second period, press the panic button for one second and release both buttons at the same time. A chime should sound within three seconds to indicate the vehicle has entered programming mode.

4. Press the LOCK and UNLOCK buttons simultaneously on the same remote used in step 3. then release. You should hear an audible tone indicating that the remote was recognized. Once tone is heard press and release the UNLOCK button on that remote. A chime should sound indicating that the remote has been programmed. This must be done within 30 seconds of step 3. Within 30 seconds of completing step 4. press the LOCK and UNLOCK button on the next remote then release. You should hear an audible tone indicating that the remote was recognized. Once tone is heard press and release the UNLOCK button on that remote. A chime should sound indicating that the remote has been programmed.  

5. Repeat step for all additional remotes including working remotes.

6. Programming is now complete. Turn ignition off and test remotes to ensure proper programming.

If this does not work may more attempts. ****PLEASE NOTE**** If you have issues with programming run through the process even if you're not correctly hearing the chimes. Some vehicles have went through programming succesfuly and did not chime as stated in directions.